The effect of increasing the multiplicity of flow fields contact surface on the performance of PEM fuel cell

Document Type : Research Paper

Authors

1 Faculty of Mechanical Engineering, University of Tabriz, Tabriz, Iran

2 Mechanical Engineering Faculty, Sahand University of Technology, Tabriz, Iran

Abstract

In this paper, three innovative 3-D geometries for flow fields of cathode and anode have been developed to investigate the comparative impact of increasing the multiplicity of the involved anode-cathode channel surface contact on the efficiency of electrochemical reaction via the same membrane electrode assembly (MEA) active area. In the introduced new models, each anode channel includes two, three and four cathodes while the convectional model include a one to one connection. The governing equations consist of mass, momentum and energy conservation. In addition, the species transport and the electric/ionic fields were solved numerically using the finite volume method under the assumptions of steady state and non-isothermal fluid flow. Simulation results revealed that increasing the multiplicity of the anode-cathode involved surface of reactants channel leads to current and power density enhancement due to the improved opportunity of reactants penetration and less concentration losses. Also, a considerable reduction of mono-cell volume size and costs for the new models in comparison with the base design was achieved. 

Keywords

Main Subjects

References

[1] Xing L., Cai C., Liu X., Liu C., Scott K., Yan Y., "Anode partial flooding modeling of proton exchange membrane fuel cells: Optimization of electrode properties and channel geometries", Chemical Engineering Science, 2016, 146:88.
[2] Jeon Y., Na H., Hwang H., Park J., Hwang H., Shul Y., "Accelerated life-time test protocols for polymer electrolyte membrane fuel cells operated at high temperature", Int J Hydrogen Energy, 2015, 40:3057.
[3] Verma A., Pitchumani R., "Influence of transient operating parameters on the mechanical behavior of fuel cells", Int J Hydrogen Energy, 2015, 40:8442.
[4] Taspinara R., Litster S., Kumbur EC., "A computational study to investigate the effects of the bipolar plate and gas diffusion layer interface in polymer electrolyte fuel cells", Int J Hydrogen Energy, 2015, 40:7124.
[5] Kim YS., Kim SI., Lee NW., Kim MS., "Study on a purge method using pressure reduction for effective water removal in polymer electrolyte membrane fuel cells", Int J Hydrogen Energy, 2015, 40:9473.
[6] Sadeghifar H., Djilali N., Bahrami M., "Thermal conductivity of a graphite bipolar plate (BPP) and its thermal contactresistance with fuel cell gas diffusion layers: effect of compression, PTFE, micro porous layer (MPL), BPP out-offlatness and cyclic load", J Power Sources, 2015, 273:96.
[7] Sadeghifar H., Djilali N., Bahrami M., "A new model for thermal contact resistance between fuel cell gas diffusion layers and bipolar plates", J Power Sources, 2014, 266:51.
[8] Sadeghifar H., Djilali N., Bahrami M., "Effect of polytetrafluoroethylene (PTFE) and micro porous layer (MPL) on thermal conductivity of fuel cell gas diffusion layers: modeling and experiments", J Power Sources, 2014, 248:632.
[9] Sadeghifar H., Bahrami M., Djilali N., "A statistically based thermal conductivity model for PEMFC gas diffusion layers", J Power Sources, 2013, 233:369.
[10] Wei Zh., Su K., Sui Sh., He A., Du Sh., "High performance polymer electrolyte membrane fuel cells (PEMFCs) with gradient Pt nanowire cathodes prepared by decal transfer method", Int J Hydrogen Energy, 2015, 40:3068.
[11] Mert SO., Ozcelik Z., Dincer I., "Comparative assessment and optimization of fuel cell", Int J Hydrogen Energy, 2015, 40:7835.
[12] Limjeerajarus N., Charoen-amornkitt P., "Effect of different flow field designs and number of channels on performance of a small PEFC", Int J Hydrogen Energy, 2015, 40:7144.
[13] Arvay A., French J., Wang JC., Peng XH., Kannan AM., "Nature inspired flow field designs for proton exchange membrane fuel cell", Int J Hydrogen Energy, 2013, 38:3717.
[14] McKahn DA., "Influence of gas channel depth in self humidified miniature PEM fuel cells with dead-ended anode", Int J Hydrogen Energy, 2015, 40:7168.
[15] Ghanbarian A., Kermani M.J., "Enhancement of PEM fuel cell performance by flow channel indentation", Energy Conversion and Management, 2016, 110:356.
[16] Rahimi-Esbo M., Ranjbar A.A., Ramiar A., Alizadeh E., Aghaee M., "Improving PEM fuel cell performance and effective water removal by using a novel gas flow field:, Int J Hydrogen Energy, 2016, 41:3023.
 
[17] Vazifeshenas Y., Sedighi K., Shakeri S., "Numerical investigation of a novel compound flowfield for PEMFC performance improvement:, Int J Hydrogen Energy, 2015, 40:15032.
 
[18] Torkavannejad A., Sadeghifar H., Pourmahmoud N., Ramin F., "Novel architectures of polymer electrolyte membrane fuel cells: Efficiency enhancement and cost reduction", Int J Hydrogen Energy, 2015, 40:12466.
[19] Rostami L., GholyNejad P., Vatani A., "A numerical investigation of serpentine flow channel with different bend sizes in polymer electrolyte membrane fuel cells", Energy, 2016, 97 400.
 
[20] Pourmahmoud N., Rezazadeh S., Mirzaee I., MotalebFaed S., "A computational study of a three-dimensional proton exchange membrane fuel cell (PEMFC) with conventional and deflected membrane electrode", J Mech Sci Techno, 2012, 26:2959.
[21] Torkavannejad A., Pourmahmood N., Mirzaee I., Ramin F., "Effect of gas flow channel on the performance of proton exchange membrane fuel cell", Indian Journal of Science and Technology, 2014, 4:619.
[22] Imanmehr S., Pourmahmoud N., "Parametric study of bipolar plate structural parameters on the performance of proton exchange membrane fuel cell:, ASME J Fuel Cell SciTechnol, 2012, 9:1.
[23] Bilgili M., Bosomoiu M., Tsotridis G., "Gas flow field with obstacles for PEM fuel cells at different operating conditions", Int J Hydrogen Energy, 2015, 40: 2303.
 
[24] Ramin F., Torkavannejad A., Baheri S., "The effect of inclined radial flow in proton exchange membrane fuel cells performance", "Hydrogen of Journal & Cell Fuel, 2014, 3:141.
[25] Tiss F., Chouikh R., Guizani A., "A numerical investigation of reactants transport in a PEM fuel cell with partially blocked gas channel", Energy Conversion Management, 2014, 80:32.
[26] Khazaee I., Ghazikhani M., "Three-dimensional modeling and development of the new geometry PEM fuel cell", Arabian Journal for Science and Engineering, 2013, 38:1551.
 
[27] Al-Baghdadi S., Al-JanabiHaroun S., "Parametric and optimization study of a PEM fuel cell performance using three-dimensional computational fluid dynamics model", Renew Energy, 2007, 32:107.
 
[28] Sadeghifar H., Djilali N., Bahrami M., "Thermal conductivity of a graphite bipolar plate (BPP) and its thermal contact resistance with fuel cell gas diffusion layers: effect of compression, PTFE, micro porous layer (MPL), BPP out-of-flatness and cyclic load", J. Power Sources, 2015, 273:96.
 
[29] Marcinkoski J., Jacob S., "Fuel Cell System Cost", DOE Hydrogen and Fuel Cells Program Record, September 25, 2014.

Files

Share

How to cite

Statistics