Performance Improvement of PEM Fuel Cells Using Air Channel Indentation; Part I: Mechanisms to Enrich Oxygen Concentration in Catalyst Layer

Document Type : Research Paper


1 Fuel Cell Laboratory, Energy Conversion Research Lab, Department of Mechanical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran

2 Amirkabir University of Technology (Tehran Polytechnic)


A three dimensional, compressible, steady, one phase flow of reactant-product mixture in the air side electrode of proton exchange membrane fuel cell (PEMFC) is numerically studied in this paper. The mixture is composed of three species: oxygen, nitrogen and water vapor. The performance of the cell is enhanced by partial blockage of the flow field channels. Various types of these blocks also called as dents in this study are considered. Examples of the dent profile shapes are: square (labeled as SQ case in this paper), semicircle (or SC) and trapezoid (or TR), and the enhancements are compared with that of no dent (or ND) case. It is observed that channel indentation can enhance the content of oxygen concentration at the face of catalyst layer up to 18%. It is noted that the content of oxygen at the face of catalyst is the driving moment for the kinetics of reaction within the catalyst layer. Hence channel indentation can be considered as a proper mechanism to enhance the performance of fuel cells. In this paper only the increasing of driving moment is discussed and the analysis of net power enhancement will be discussed later in another paper.


Main Subjects

1. Wang X., Duan Y., Yan W. and Peng X., “Local transport phenomena and cell performance of PEM fuel cells with various serpentine flow field designs”, J. Power Sources, 2008, 175:397
2. Ramesh P. and Duttagupta S.P., “Effect of channel dimensions on Micro PEM fuel cell performance using 3D modeling”, Int. J. Renewable Energy Research, 2013, 3, No. 2
3. Choghadi H.R. and Kermani M.J., “15% efficiency enhancement using novel partially interdigitated serpentine flow field for PEM fuel cells”, 10Th International Conference on Sustainable Energy Technologies SET2011, Istanbul, Turkey, 4-7 Sep. 2011
4. Bernardi D.M. and Verbrugge M.W., “A mathematical model of the solid-polymer-electrolyte fuel cell”, J. Electrochem.1992, 139
5. Khakbaz Baboli M. and Kermani M.J., “A two-dimensional, transient, compressible isothermal and two-phase model for the air side electrode of PEM fuel cell”, J. Electrochemical Acta, 2008, 53:7644
6. Heidary H. and Kermani M.J., “Performance enhancement of fuel cells using bipolar plate duct indentations’, Int. J. Hydrogen Energy, 2012, 38:5485
7. Yuan W., Tang Y., Pan M., Z. Li and Tang B., “Model  of prediction of effects of operating parameters on proton exchange membrane fuel cell performance”, J. Renewable Energy, 2010, 35:656
8. Perng S.W., Wu H.W., Jue T.C. and Cheng K.C., “Numerical predictions of a PEM fuel cell performance enhancement by a rectangular cylinder installed transversely in the flow channel”, J. Applied Energy, 2009, 86:1541
9. Natarajan D. and Van Nguyen T., “A two dimensional two phase multi component transient model for the cathode of a proton exchange membrane fuel cell using conventional gas distributors”, J. Electrochemical Society, 2001, 148:1324
10. Guo Z.Y., Li D.Y. and Wang B.X., “A novel concept for convective heat transfer enhancement”, Int. J. Heat and Mass Transfer, 1998, 41:2221
11. Tao W.Q., Guo Z.Y. and Wang B.X., “Field synergy principle for enhancing convective heat transfer its extension and numerical verifications”, Int. J. Heat and Mass Transfer, 2002, 45:3849
12. Tao W.Q., He Y.L., Wang Q.W., Qu Z.G. and Song F.Q., “A unified analysis on enhancing single phase convective heat transfer with field synergy principle”, Int. J. Heat and Mass Transfer, 2002, 45:4871
13. Guo Z.Y., Tao W.Q. and Shah R.K., “The field synergy (coordination) principle and its applications in enhancing single phase convective heat transfer”, Int. J. Heat and Mass Transfer, 2005, 48:1797
14. Heidary H. and Kermani M.J., “Enhancement of heat exchange in a wavy channel linked to a porous domain; a possible duct geometry for fuel cells”, Int. J. Heat and Mass Transfer, 2012, 39:112