A new approach to microstructure optimization of solid oxide fuel cell electrodes

Document Type : Research Paper

Authors

1 Mechanical Engineering Department, Babol Noshirvani University of Technology, Babol, Iran

2 3School of Mechanical Engineering, College of Engineering, University of Tehran

3 School of Mechanical Engineering, College of Engineering, University of Tehran

Abstract

Designing optimal microstructures for solid oxide fuel cell (SOFC) electrodes is complicated due to the multitude of electro-chemo-physical phenomena taking place simultaneously that directly affect working conditions of a SOFC electrode and its performance. In this study, a new design paradigm is presented to obtain a balance between electrochemical sites in the form of triple phase boundary (TPB) density and physical properties in the form of gas diffusivity in the microstructure of a SOFC electrode. The method builds on top of a previously developed methodology for digital realization of generic microstructures with different geometric properties in ionic or electronic conductor grains. The obtained realizations of SOFC electrode are then used to calculate TPB density and gas transport factor. In the next step, based on the obtained database, a neural network is trained to relate input geometrical parameters to those output properties. The results indicate that the TPB density is less sensitive to the geometry than the gas transport factor. Also, the smaller particles in the ionic and electronic conductor phase lead to a higher amount of TPB density. The presented methodology is also used to obtain the maximum feasible properties of microstructures and their related geometric characteristics for special target functions like maximum reaction sites and gas diffusivity in a realized model. The tradeoff between input and output parameters is another application of this modeling approach which   demonstrates the TPB density and gas transport factor variation versus the geometric anisotropy of particles and porosity, respectively.

Keywords

Main Subjects

References

1.  Andersson, M., J. Yuan, and B. Sundén, "SOFC modeling considering electrochemical reactions at the active three phase boundaries", International journal of heat and mass transfer, 2012. 55(4): p. 773-788.
2.  Matsuzaki, Y. and I. Yasuda, "Electrochemical properties of reduced-temperature SOFCs with mixed ionic–electronic conductors in electrodes and/or interlayers", Solid State Ionics, 2002. 152: p. 463-468.
3.  Choi, J.H., J.H. Jang, and S.M. Oh, "Microstructure and cathodic performance of La 0.9 Sr 0.1 MnO 3/yttria-stabilized zirconia composite electrodes", Electrochimica Acta, 2001. 46(6): p. 867-874.
4.  Murray, E.P., T. Tsai, and S.A. Barnett, "Oxygen transfer processes in (La, Sr) MnO 3/Y 2 O 3-stabilized ZrO 2 cathodes: an impedance spectroscopy study", Solid State Ionics, 1998. 110(3): p. 235-243.
5.  Yokokawa, H., et al., "Fundamental mechanisms limiting solid oxide fuel cell durability", Journal of Power Sources, 2008. 182(2): p. 400-412.
6.  McIntosh, S., et al., "Effect of polarization on and implications for characterization of LSM-YSZ composite cathodes", Electrochemical and Solid-State Letters, 2004. 7(5): p. A111-A114.
7.  Zhao, F., et al. "The effect of electrode microstructure on cathodic polarization. in Proceedings of the Seventh International Symposium on Solid Oxide Fuel Cells", 2001. The Electrochemical Society, Pennington, NJ.
8.  Wilson, J.R., et al., "Effect of composition of (La 0.8 Sr 0.2 MnO 3–Y 2 O 3-stabilized ZrO 2) cathodes: Correlating three-dimensional microstructure and polarization resistance", Journal of Power Sources, 2010. 195(7): p. 1829-1840.
9.  Wilson, J.R., et al., "Quantitative three-dimensional microstructure of a solid oxide fuel cell cathode", Electrochemistry Communications, 2009. 11(5): p. 1052-1056.
10. Haanappel, V., et al., "Optimisation of processing and microstructural parameters of LSM cathodes to improve the electrochemical performance of anode-supported SOFCs", Journal of Power Sources, 2005. 141(2): p. 216-226.
11. Schmidt, V.H. and C.-L. Tsai, "Anode-pore tortuosity in solid oxide fuel cells found from gas and current flow rates", Journal of Power Sources, 2008. 180(1): p. 253-264.
12. Jeon, D.H., J.H. Nam, and C.-J. Kim, "Microstructural optimization of anode-supported solid oxide fuel cells by a comprehensive microscale model", Journal of The Electrochemical Society, 2006. 153(2): p. A406-A417.
13. Sebdani, M.M., et al., "Designing an optimal 3D microstructure for three-phase solid oxide fuel cell anodes with maximal active triple phase boundary length (TPBL)", International Journal of Hydrogen Energy, 2015. 40(45): p. 15585-15596.
14. Riazat, M., et al., "Investigation of the property hull for solid oxide fuel cell microstructures", Computational Materials Science, 2017. 127: p. 1-7.
15. Baniassadi, M., et al., "Three-phase solid oxide fuel cell anode microstructure realization using two-point correlation function", Acta materialia, 2011. 59(1): p. 30-43.
16. Adams, B.L., S. Kalidindi, and D.T. Fullwood, "Microstructure-sensitive design for performance optimization", 2013: Butterworth-Heinemann.
17. Baniassadi, M., et al., "New approximate solution for N-point correlation functions for heterogeneous materials", Journal of the Mechanics and Physics of Solids, 2012. 60(1): p. 104-119.
18. Janardhanan, V.M., V. Heuveline, and O. Deutschmann, "Three-phase boundary length in solid-oxide fuel cells: A mathematical model", Journal of Power Sources, 2008. 178(1): p. 368-372.
19. He, W., W. Lv, and J. Dickerson, "Gas transport in solid oxide fuel cells", 2014: Springer.
20. Zhao, F., T.J. Armstrong, and A.V. Virkar, "Measurement of O 2 N 2 Effective Diffusivity in Porous Media at High Temperatures Using an Electrochemical Cell", Journal of the Electrochemical Society, 2003. 150(3): p. A249-A256.
21. Fleig, J. and J. Maier, "The polarization of mixed conducting SOFC cathodes: Effects of surface reaction coefficient, ionic conductivity and geometry", Journal of the European Ceramic Society, 2004. 24(6): p. 1343-1347.
22. Fullwood, D.T., et al., "Microstructure sensitive design for performance optimization", Progress in Materials Science, 2010. 55(6): p. 477-562.
23. Tanner, C.W., K.Z. Fung, and A.V. Virkar, "The effect of porous composite electrode structure on solid oxide fuel cell performance I. Theoretical analysi", Journal of The Electrochemical Society, 1997. 144(1): p. 21-30.
24. Kishimoto, M., et al., "Towards the Microstructural Optimization of SOFC Electrodes Using Nano Particle Infiltration", ECS Transactions, 2014. 64(2): p. 93-102.

Files

Share

How to cite

Statistics